Car Audio Advice | Stereo Terminology And Education

INSTALLING A CAPACITOR

So, you've brought home your shiny new capacitor in the bag. If this is your first cap installation, your first hope is that it came with good installation instructions. If not, or if you just want to know how its done, perhaps this article will get you off to a good start.

Some capacitors require you to pre-charge them to attain usability mode. To do this, you will need the charging board that comes with the unit. It is usually a simple PC board card with a positive and negative 16 gauge wires. Simply follow the included instructions, administering the power wire from a 12V source to your cap's positive terminal. Don't forget to ground it too. Now connect the card, positive-to-positive and negative-to-negative (or ground). When the indicator on the card comes on, the capacitor is fully pre-charged.

At this point, its time for the installation. Select a good spot, no more than 18" from the amplifier on the + power wire. Cut the power wire on the amp at the location where the cap is to go, and connect the wire to the positive terminal. If you are using ring terminals, install the first one flat on the base of the terminal. Then, run the second half of the spliced power wire from the same positive terminal (set the second ring right on top of the first one) and run it to the fuse block. If you are installing a model that uses a distribution block cap, simply hook the wire to the amp in the appropriate slot, and the 12V lead (to battery) in the appropriate slot. As always, follow the instructions.

Don't forget about the ground (-) connection! The cap should be grounded close by, preferably in the same spot the amp is grounded. Using the same gauge wire, run the ground cable to the negative terminal (usually the one not marked). Next, if your cap came with a remote lead terminal, run this to either the ACC fuse in your fuse block or to the REMOTE/ANT lead on your receiver using 16 gauge or so wiring. With the wiring all in place, secure the cap into place using an included bracket (if included) or using some 3" pipe brackets from Home Depot. You can install the cap right side up, upside down, side ways, diagonally, or whatever. Just make sure the vent at the top is never covered or blocked.

You can now proceed to safely reconnect your battery terminals. Sit back and enjoy cleaner, crisper and faster response, from your bass system.

For more on the theory and benefits of capacitors, see our article in this section.





Technical Help & Education Glossary Of Terms Speakers Main Page How Speakers Work Choosing Speakers What's A Woofer? What's A Midrange? What's A Tweeter? Other Speaker Types More Speaker Types What's A Capacitor? Installing A Capacitor What's A Crossover? What's An Equalizer? Speaker Enclosures Theile/Small Param. About Power Amps Installing An Amp Installation Tips Power Ratings Installing/Replacing Head Units/Receivers Installing Neon/LED Eliminating Noise Use The Right Tools Manufacturer's Links Personal & Marine Electronics Laptop Computers Cell Phones & PDAs Portable TV & Video Electronic Readers MP3/Music Players CD Players/Booms Earphones/Buds Digital Cameras Video Cameras Personal GPS Bluetooth Calculators Accessories Marine Electronics Stereo Amplifiers Stereo Speakers Stereo Woofers Enclosed Speakers TVS & Video CD/Mp3 Receivers GPS & Navigation Fish Finders Accessories Home Stereo & Office Electronics Flat Screen & HD TVs Surround Sound Home Theater DVD Players/Tivo DVD Recorders Blu-Ray Devices Amplifiers/Tuners Speaker Systems Subwoofer Drivers Midrange Drivers Tweeter Drivers Powered Subwoofers Outdoor Speakers Stereo Accessories Digital Photo Frames Video Game Systems Game Accessories Video Games Home Security/Alarms Computer Products Desktops & Laptops Add-Ons/Peripherals Computer Monitors Computer Software Computer Games Printers & Scanners Ink/Specialty Papers Parts & Components Computer Supplies Security/Tech Support Auto Electronics Amplifiers Subwoofers Full-Range Speakers Midrange Speakers Tweeters Power Capacitors Empty Enclosures Loaded Enclosures CD/Mp3 Receivers CD Changers Bass Packages Car TV & Video Satellite Radio Bluetooth Wireless GPS Navigation Neon/LED Lighting Radar Detectors Chrome Mufflers Car Alarms/Security V AUTO PARTS STORE Auto Wiring & Accessories Air Horns Power Antennas Antenna Boosters A/V Controllers Bass Blockers Crossovers Dynamat Equalizers Fans (Cooling) FM Modulators Interfaces Line Converters Noise Filters Power Inverters Power Supplies RCA Cables RCA Splitters Remote Controls Signal Boosters Vibration Control Speaker Grills Wiring Kits		INSTALLING A CAPACITOR So, you've brought home your shiny new capacitor in the bag. If this is your first cap installation, your first hope is that it came with good installation instructions. If not, or if you just want to know how its done, perhaps this article will get you off to a good start. Some capacitors require you to pre-charge them to attain usability mode. To do this, you will need the charging board that comes with the unit. It is usually a simple PC board card with a positive and negative 16 gauge wires. Simply follow the included instructions, administering the power wire from a 12V source to your cap's positive terminal. Don't forget to ground it too. Now connect the card, positive-to-positive and negative-to-negative (or ground). When the indicator on the card comes on, the capacitor is fully pre-charged. At this point, its time for the installation. Select a good spot, no more than 18" from the amplifier on the + power wire. Cut the power wire on the amp at the location where the cap is to go, and connect the wire to the positive terminal. If you are using ring terminals, install the first one flat on the base of the terminal. Then, run the second half of the spliced power wire from the same positive terminal (set the second ring right on top of the first one) and run it to the fuse block. If you are installing a model that uses a distribution block cap, simply hook the wire to the amp in the appropriate slot, and the 12V lead (to battery) in the appropriate slot. As always, follow the instructions. Don't forget about the ground (-) connection! The cap should be grounded close by, preferably in the same spot the amp is grounded. Using the same gauge wire, run the ground cable to the negative terminal (usually the one not marked). Next, if your cap came with a remote lead terminal, run this to either the ACC fuse in your fuse block or to the REMOTE/ANT lead on your receiver using 16 gauge or so wiring. With the wiring all in place, secure the cap into place using an included bracket (if included) or using some 3" pipe brackets from Home Depot. You can install the cap right side up, upside down, side ways, diagonally, or whatever. Just make sure the vent at the top is never covered or blocked. You can now proceed to safely reconnect your battery terminals. Sit back and enjoy cleaner, crisper and faster response, from your bass system. For more on the theory and benefits of capacitors, see our article in this section.		MAIN PAGE GLOSSARY SPEAKERS: Choosing General Woofers Miidrange Tweeters Full-Range Full-Range 2 CAPACITORS CROSSOVERS EQUALIZERS	ENCLOSURES: Theile/Small AMPLIFIERS: About Installing Install Tips Power Ratings RECEIVERS: Installing NEON/LED: Installing TOOLS

	Home -- Policies -- Products -- Tech Center -- Auto Electronics -- Home Electronics -- Personal & Marine Electronics -- Stereo Tech Info Website Designed & Maintained by MetroDirect Communications Copyright (c) 2000 - 2009 Electronixwarehouse.com . Use of any material appearing on this site without specific written permission is prohibitied by law. electronixwarehouse.com --- logobannerfactory.com --- bleepthem.com (Political Satire) --- rlebeaux.com --- stereotechnicalinformation.com (Stereo Technical Help) --- electronixwarehouse.net --- thespeakerstore.com --- wmpublishing.com (Help For Writers) --- barbarathenovel.com --- cutethenovel.com
--			--